Slotcars

Welcome to C & R Raceway

General Rules:

 Raceway Responsibilities:

 

1.     Raceway will open tech 30 minutes prior to any scheduled race is to begin..

2.     All cars will be teched and impounded.

3.     All impounded cars will be taken to the track for the start of the race.

4.     Track time between classes will be a maximum of 15 minutes.

 

Racer Responsibilities:

 

1.     Racers must participate in corner marshaling.  Racers must marshal the same class as they race.

2.     Cars must be available for tech-in during the race prior to the class you are racing.

3.     Anyone caught cheating will FORFEIT all points and winning for that class, on that day.

4.     Cooperation from everyone to conduct races on a timely basis.

5.     Sportsmanlike conduct is MANDATORY.

6.     Marshal abuse will NOT be tolerated.

a.     First offense will result in a deduction of 5 laps.

b.     Second offense will result in a 10 lap deduction.

c.      Third offense will result in an EXPULSION from that class for that day.

 

Lap Counter:

 

1.     The lap counter will be considered correct unless it can be proven otherwise.  If a major error occurs in the counting process that cannot be corrected, the race director may:

a.     Assign responsible stewards to count laps or verify the counter.

b.     Restart the segment.

c.      Restart the race form the last possible point.

2.     For a major error in counting, the steps taken should preserve as much of the race as possible, while remaining as fair as possible.

3.     There will be NO ADDING or subtracting of laps due to drivers inability to control his car or marshaling error.

4.     If the car skids past or over the counter, the car goes back on where it stops AFTER the lap counter.

 

 

Track Calls:

 

1.     The power will only turned off for extremely unfair or dangerous situations.  The following are the only acceptable reasons:

a.     Braid up.

b.     Power failure.

c.      Debris in the slot.

d.     An Unmarshalable car.

e.      Lap counter or track equipment failure.

f.       Insufficient number of marshals at President’s discretion.

g.     Too many cars off is NOT a track call.

2.     During the track call, there will be absolutely no work performed on the car or lane.  Doing so will result in a 20 lap penalty.  A second infraction will result in a disqualification.  This includes work on the car or lane by pit helpers of the driver.

 

Black Flag:

The race director is obliged to black flag any car, which is dragging, interfering with other cars or continuously de-slotting due to mechanical problems.  Upon being black flagged, the driver must bring the car in for repairs immediately.  If the problem is not corrected, the black flag may be enforced again as required.

 

Lane Change:

All drivers are required to use a lane change card in-between heats.

 

Protests:

Anybody can protest a look for $5.00, but if the car needs to be taken apart, it will cost $10.00 more.  Anybody can protest anything if they put up $10.00.  Then the $10.00 will go to the race series.  Then, a NORTH CENTRAL/S.C.O.R.E. official will take apart the car and check for any illegal parts.

 

Race Format:

For all NC USSCA classes will run 3 minute heats with a 2 minute lane change.  All SCORE oval races will run 2 minute heats with a 2 minute lane change.

 

Entry Fees:

All race entries at C & R Raceway will be $5.00 a race.  Entry fees may rise for any special or National Events.

 

4'' Retro NASCAR

CHASSIS:
1. Any 4" chassis that is commercially available and approved by USSCA
2. Must be stamped and formed metal only.
3. May brace chassis in any way you would like.
4. A steel guide tongue reinforcement may be used, but the original guide tongue may not be removed, modified, or moved.
 

OVAL
1.  Offset should not stick out more than an 1/8" of an inch of the chassis

Gears/Axles/Wheels
1.  48 pitch or 64 pitch only
2.  3/32 or 1/8 solid steel axles only.
3.  Front wheels .500 minimum
4.  Rear tires must be black foam, .750 minimum
6.  Maximum width is 3 ¼.
7.  .062 clearance at the back, up to the rear axle
8.  No tech at the front
 

LEAD WIRES:
1.  Magnet wire or magnet type wire is not allowed.
2.  Guide clips are allowed.
3.  May add wire guide or retainer.

BODIES
1. Body must be commercially available and on approved body list.
2. 1/8" minimum front and rear bumper
3. Maximum rear spoiler height of 1 5/8", measured from the tech block to the top of the spoiler.
4. Must have three scale appearing numbers
5. Body must be fully painted and cover the entire chassis
6. May reinforce body with tape or lexan
7. All windows must be clear and retain factory lexan
8. Front wheel wells may be cut out or left clear. No cutting into the top of the fenders.
9. Body must have fully painted 3-D lexan interior. Paper interiors of ANY kind are NOT LEGAL.  Chassis or track must not be visible.
 

MOTORS
1.  Any JK Falcon Motors can be used.  Hawk motors are not allowed.

 

Falcon Eliminator

 

CHASSIS:
1. Any type of chassis.
2. Must be stamped and formed metal only.
3. May brace chassis in any way you would like.
 

Gears/Axles/Wheels
1.  Any Gear Ratio.
2.  3/32 or 1/8 solid steel axles only.
3.  Any size front wheels are required and they must turn.
4.  Rear tires must be a minimum of .500 wide.  No height restrictions.
 

LEAD WIRES:
1.  Magnet wire or magnet type wire is not allowed.
2.  Guide clips are allowed.
3.  May add wire guide or retainer.

BODIES
1. The body must be a 1/24th or 1/25th scale 1970’s and under sedan/door slammer style body. 

2. No body modifications allowed except for hood scoops. No custom rear wings allowed.
3. Body must be fully painted and cover the entire chassis
4. May reinforce body with tape or lexan
5. All windows must be clear and retain factory lexan.

6. All cars must weight a minimum of 120 grams.
7. Body must have fully painted 3-D lexan interior. Paper interiors of ANY kind are NOT LEGAL.  Chassis or track must not be visible.

MOTORS
1. Any JK Falcon Motors can be used.  Hawk motors are not allowed.

 

 Parma Edge

 

CHASSIS:
1. Only Parma Edge Chassis as delivered by the manufacture as a RTR Style..
2. Must be stamped and formed metal only.

3.  Chassis cannot be lightened or modified in any way.

Gears/Axles/Wheels
1.  Must use 9 tooth pinion as delivered from the manufacturer.  May use any Parma crown gear.
2.  Front and rear axles from the RTR kit must be used.  1/8 solid steel axles only.

3.  May solder the rear bushings into place.
4.  Must use rear tires as delivered from the manufacturer in the RTR kit.

5.  Front tires must be as delivered from the manufacturer in the RTR kit.

6.  Factory Wheelie bars and wheels must be used.

7.  Wheelie bar may be soldered into the chassis.

LEAD WIRES:
1.  Must use original wires from the RTR kit.
2.  May use guide clips to solder wires.
3.  May add wire guide or retainer.

BODIES
1. Any Parma Edge lexan body that is available on the RTR Edge kit.. 

2. No body modifications allowed except for hood scoops. No custom rear wings allowed.
3. Body must be fully painted and cover the entire chassis
4. May reinforce body with tape or lexan
5. All windows must be clear and retain factory lexan.

6. All cars must weight a minimum of 120 grams.
7. Body must have fully painted 3-D lexan interior. Paper interiors of ANY kind are NOT LEGAL.  Chassis or track must not be visible.

 

MOTORS
1. Must be a S16D Sealed motor (#502). The seal cannot be broken.

2. Can Bushings may be soldered into place however the 2-56 motor screws must also remain installed.

3. Motor cannot be ground down.

4. Brushes and Springs may be changed.

4" NASCAR

Scale:

1/24

Design:

Flexi Chassis

Body:

Lexan

Motor:

Falcon 7

Track:

Oval

4 1/2" FCR NASCAR

Scale:

1/24

Design:

FCR Chassis

Body:

Hardbody

Motor:

Deathstar

Track:

Oval

 

4" GT 1

Scale:

1/24

Body:

Lexan

Motor:

Falcon 7 or Hawk

Track:

LTD

 

Indy F1

Scale:

1/24

Body:

Lexan

Motor:

Falcon 7

Track:

LTD

 

4 1/2" FCR SPRINT CAR

 

Scale:

1/24

Design:

4 1/2" FCR Parma

Body:

Parma Sprint Car Lexan

Motor:

Deathstar

Track:

Oval

 

H.O.

 

Scale:

1/64

Design:

Super Stock

Body:

Lexan

Track:

H.O. Bucktrack

1/32 Production

Scale:

1/32

Design:

Cheetah 11

Body:

GT 1 Lexan

Motor:

Falcon 7

Track:
LTD Flat Track or Grandstand

 

HOME SET CARS

Scale:

1/32

Design:

SCX, Scale Electric, FLY, Slot-It, 1/24 BRM

Track:

Flat Track

 

DRAG RACING CARS

Scale:

1/24

Design:

Any and all Class Racing and Bracket Racing

Track:

98' Drag Track

 

 

Phone:

815-933-RACE(7223)